30 years of innovation,
quality and service on demand.
18IM
18M series includes submersible electronic level transmitters with
4÷20mA output proportional to hydrostatic pressure detected
by means of a piezoresistive sensor based on resistive Wheatstone
bridge diffused on a chip. All 18IM series versions have housing Ø18
mm and fixed ranges. 18IM Series transmitters are used in all
industrial applications to measure level of liquids in wells,
chests, lakes, water treatment plants, tanks, etc.
27IM
27IM series includes submersible electronic level transmitters
for hydrostatic pressure sensing, available with piezoresistive
(P series)
or ceramic (C series) sensor. All 27IM series versions has small
sizes (housing ØMax 35 mm) and fixed ranges. 27IM Series
transmitters are used in industrial and marine applications
to measure level of liquids in wells, chests, lakes, water
treatment plants, tanks, etc.
T7IM
T79-IM series includes SMART electronic transmitters with 4÷20
mA output and HART® digital communication protocol available
with piezoresistive (P series) or Ceramic (C series) sensor.
Piezoresistive sensor are based on silicon chip resistive
Wheatstone bridge while ceramic sensors are thick film sensors
based on strain gauge principle with backplate and diaphragm in
ceramic material; in both versions the sensors are calibrated
individually together with their own seal. Configurations and
adjustments can be made locally, by means of push buttons and
display, or remotely using HART® communication protocol.
85DL
Series 85DL pressure tranducers with datalogger, battery supplied,
measure relative and absolute pressures, with ranges from 100
mbar up to 75 bar. Transducer’s housing is manufactured
in St.St.
AISI 316 with standard process connection ½”GM (other
standards
available).
The submersible version is suitable for the measuring of liquids’
level in wells, chests and tanks, and is composed by two St.St.
AISI
316 bodies, connected with a self supporting cable with variable
27
27 series includes electronic pressure transmitters available with
piezoresistive (P series) or Ceramic (C series) sensor. All
27 series
versions has small sizes (typical housing Ø27 mm) and fixed
ranges (when possible to adjust zero and span, this can be done
within ± 10%). 27 Series transmitters are used in industrial
and marine applications detect pressure of liquids, gas and vapours.
85
Series 85 sensors are based on a piezo-resistive silicon chip, temperature compensated. Their versatility and the small dimensions makes them suitable for various applications of pressure measuring of gas, vapours and liquids.
T7N
T7N series includes SMART electronic transmitters with 4÷20
mA output and HART® digital communication protocol available
with piezoresistive (P series) or Ceramic (C series) sensor. In
both versions the sensors are calibrated individually together
with their own seal. Configurations and adjustments can be made
locally by means of push buttons and display or remotely using
HART® protocol compatible communicators. T7N Series transmitters
are used in industrial applications to detect pressure and level
of liquids, gas and vapours. Our technical office is at your disposal
for special applications.
T79
T79 series includes electronic transmitters featured by all AISI316L
St.St. execution, and housing available with direct bottom or back
process connections.
Electronics is available in the following executions:
a) Smart type with 4-20mA + HART® protocol output, complete
with digital display and push buttons for local configuration.
b) Smart type with 4-20mA + HART® protocol output, without
digital display and push buttons (remote configuration through
HART® communicators)
c) Smart type with 4-20 mA analogue output only, without digital
display; data acquisition by means of push buttons.
T7D
T7D series includes differential pressure SMART electronic transmitters
with 4÷20 mA output and HART® digital communication
protocol. Configurations and adjustments can be made locally
by means of push buttons and display or remotely using HART® protocol
compatible communicators. T7D Series transmitters are used
in industrial applications to measure absolute relative or
differential pressures of liquids, gas and vapours, to measure
relative or differential level of liquids and to measure the
flow rate (output can be linear or proportional to the v?p
value). Instrument’s body is designed to sustain static
pressures up to 75 bar.
T7K series includes differential pressure electronic transmitters with capacitive cell featured by all AISI316L St.St. execution and 340° rotating head. Electronics is available in the following executions: Smart with 4-20mA and HART® protocol output, complete with digital display and push buttons for local configuration or without digital display and push buttons (remote configuration through HART® communicators).
T7T
T7T series includes SMART temperature electronic transmitters with 4÷20 mA output and HART® digital communication protocol able to accept Pt 100 ohm 3 wires resistance thermometers. The transmitter is ATEX certified and can be directly mounted in hazardous areas. Configurations and adjustments can be made locally by means of push buttons and display or remotely using HART® protocol compatible communicators
T76
T76 MINISMART series includes SMART electronic pressure and differential
pressure transmitters with 4÷20 mA output and HART® digital
communication protocol. MINISMART transmitters are featured
by extremely reduced size and are available with piezoresistive
(P series) or Ceramic (C series) sensor. In both versions the
sensors are calibrated individually together with their own
seal. Configurations and adjustments can be made locally by
means of push buttons and display or remotely using HART® protocol
compatible communicators. T76 MINISMART Series transmitters
are used in industrial applications to detect pressure and
level of liquids, gas and vapours.
UPF02
Ultrasonic flowmeter UPF-02 is a next-generation instrument that
meets technically advanced ergonomic standard requirements. This
system is particularly advised to carry out measurements in severe
operating environments and in places difficult to be reached.
Ultrasonic flowmeter UPF-02 is suitable for use in flow measuring
tasks that require advanced performance, a simple installation
method and an high portability.
ASL400
ASL400 is designed for marine and on-land applications for liquid
detection, pump control, water ingress alarm systems, for high
and
low alarm level, overfilling protection on liquids with or without
foam. ASL400 works on the principle of distributed acoustic
waves
in a metal rod. If the rod is not covered by the liquid the sound
waves are dispersed freely without any interference. If liquid
covers
the rod the emission of sound waves is muffled and this interference
is picked up by the piezoelectric sensor and converted into
a current
signal in the current loop (on-off). These instruments have no
moving parts, no vibration, no optical or capacitive detectors.
They are
pure static sensors offering the maximum reliability.
TSU400
The galvanically isolated safety barriers TSU400 are valid alternative
to passive barriers because they don’t need a high integrity
I.S. ground, being the isolation between the safe area and
the hazardous area guaranteed by a transformer. TSU400 series
barriers have an intrinsic voltage regulation of the supply
and are designed for connection to ON-OFF sensors having a
mA output so that they permit to interface 5/13 mA two wire
switching instruments also giving a relay output. They are
especially suitable for ships applications and for hazardous
areas installations being certified [EEx ia] IIC. Great advantages
are offered by the use of TSU400 series barriers interfaced
with Valcom® ultrasonic level switches ASL400 series.
DSL10
DSL-10 series level switches are static sensor without moving
parts, suitable for the control of all conductive and non conductive
liquids. The detection of presence of liquid is not influenced
neither by viscosity, density, conductivity of the fluid nor
by the
presence of foams. The series is studied for granting the
maximum reliability together with the absent need of a periodic
maintenance. These instruments have been developed to be used
in extreme environmental conditions, as well as with corrosive
fluids.
PI97
PI97 series converters/transmitters measure and converts relative
and differential pressures into an electrical signal both for
standard
values (3÷15 psi or 0.2÷1 bar) and ranges from 0÷3
mbar to 0÷2 bar. The direct conversion of the pressure into
an electrical signal is achieved by a minute deflection of sensor
diaphragm which changes the resistance of the bridge with the applied
stress; changes in pressure cause a corresponding change in the
transmitter output proportionally to the bridge unbalance. A single
circuit supplies power to sensor and receives its signal providing
conversion into a standard 4÷20 mA Dc.
27M
P to I converters 27M Series are designed to interface pneumatic
0.2÷1 bar signals up to 0÷20 bar signals to controls
systems, data loggers and other data acquisition systems. The
variety of the possible connectors makes this instrument suitable
for every kind of application.
TRT
The temperature transmitter series TRT is equipped with a PT 100 ohm thermo resistance, and provides a current signal output within the 4÷20mA range (2 wires system). It can be used in different applications such as, for example, for mounting on tank ships and in all the processes which requires an accurate temperature measurement.
TDR1-13-15
TDR series transducers are working on a force balance principle
and have been realized to measure level of liquids in open
vessels
or pressure in closed systems. The models TDR1, TDR13 and TDR15
are especially used in the pulp and paper industry. The pneumatic
output signal ratio is 1:1 with the measured variable. They
are
used in connection with the pneumatic receivers and/or pressure
switches installed locally or on control panels for indication
alarm,
or in connection with pneumatic controllers for analog pneumatic
control of level and pressure..
TS02
The efforts of Valcom® in researching and developing
innovative solutions for level measurement have succeeded
in realising the Tank Sonarâ TS02 sensor (International
Patent pending). Acoustic waves guided into a Æ 28 mm
(typical) pipe installed inside the tank permit to measure the
liquid level with a very high accuracy.
RMG
RMG series includes radar level transmitters. The level of liquids is measured by transmitting low energy radar pulses towards the liquid surface and receiving the radar echoes. The travel time for the radar pulse is proportional to the distance between the gauge and the surface. The radar pulse is unaffected by the tank content and atmosphere, temperature or pressure.
A2X
The process indicators A2X series are configurable microprocessor
devices, with analog input selectable via terminal block connection
for measurements in mA or V DC Maximum display scale ± 99999
with programmable reading scale and decimal point by means
of four keys keypad and seven-segment display (character height
12.5 mm). Start and end of scale calibration in self-learning
mode through two external digital inputs and Loop interruption
monitoring with visual indicator and output override (for 4...20
mA signals) are only some of its features.
